Plumbing Basics: A Prerequisite for Installing a Bathtub
Plumbing Basics: A Prerequisite for Installing a Bathtub
Blog Article
The content down below pertaining to How to Install a Bathtub: Install an Acrylic Tub and Tub Surround is extremely informative. Check it out for yourself and figure out what you think of it.
Installing a bathtub isn't precisely rocket science, however it does call for strong plumbing, woodworking, and also in some cases, tiling skills. Changing an old tub with a new one is additionally a reasonably tough project. If the old bathtub is readily available, the job can relocate rapidly; if you have to open a wall surface to get rid of the old tub as well as place the new tub, the job is a lot harder. In either instance, the task is within a house handyman's abilities, although you will certainly require an assistant to move out the old tub as well as set in the brand-new one. Ensure you have actually certified on your own for the job as well as are comfortable trying it. As opposed to employing a professional to take control of a halfway-completed task, it is far better to consider employing one before you begin. Possibilities are you might require a specialist plumber to make tube connections.
This article will help you mount a brand-new tub in your shower room if you have already acquired a brand-new tub and do not need to change the setup of your previous water system pipes.
Your devices as well as material list ought to make up the following:
Preparing for the Installment
To start with, the sustaining structure provided with the bathroom ought to be fitted (if called for) according to the supplier's instructions. Next, fit the taps or mixer to the bathtub. When suitable the tap block, it is important to ensure that if the tap includes a plastic washing machine, it is fitted in between the bathroom and also the faucets. On a plastic bathroom, it is additionally sensible to fit a supporting plate under the taps system to stop strain on the bathtub.
Fit the flexible tap ports to the bottom of the two taps utilizing 2 nuts as well as olives (occasionally provided with the bathtub). Fit the plug-hole electrical outlet by smearing mastic filler round the sink outlet hole, and after that pass the outlet with the hole in the bath. Use the nut supplied by the producer to fit the plug-hole. Analyze the plug-hole outlet for an inlet on the side for the overflow pipeline.
Next off, fit completion of the versatile overflow pipe to the overflow outlet. After that, screw the pipeline to the overflow face which should be fitted inside the bath. Make sure you use all of the provided washers.
Link the trap to the bottom of the waste outlet on the bath tub by winding the string of the waste outlet with silicone mastic or PTFE tape, as well as screw on the catch to the electrical outlet. Connect the bottom of the overflow tube in a comparable manner.The bathroom need to now be ready to be fitted in its final setting.
Removing Old Taps
If you require to change old faucets with brand-new ones as a part of your installment, then the first thing you ought to do is detach the water system. After doing so, activate the faucets to drain pipes any type of water staying in the system. The procedure of eliminating the existing taps can be quite bothersome as a result of the restricted accessibility that is commonly the case.
Make use of a basin wrench (crowsfoot spanner) or a faucet tool to undo the nut that links the supply pipelines to the taps. Have a cloth all set for the staying water that will certainly originate from the pipelines. When the supply pipes have actually been removed, make use of the very same device to loosen up the nut that holds the faucets onto the bath/basin. You will certainly need to stop the single faucets from turning throughout this procedure. Once the taps have actually been eliminated, the holes in the bath/basin will certainly need to be cleaned of any type of old securing substance.
Prior to proceeding to fit the brand-new taps, contrast the pipe links on the old faucets to the new faucets. If the old taps are longer than the brand-new faucets, after that a shank adapter is required for the new taps to fit.
Setting up the Tub
Making use of both wood boards under its feet, put the tub in the called for placement. The wood boards are handy in equally spreading out the weight of the tub over the area of the boards rather than focusing all the weight onto 4 little points.
The next goal is to make sure that the bathtub is leveled all round. This can be accomplished by inspecting the spirit level and also adjusting the feet on the tub until the spirit level reviews level.
To mount taps, fit all-time low of the outermost flexible tap adapter to the suitable supply pipeline by making a compression join; then do the exact same for the other tap.
Switch on the water as well as examine all joints as well as new pipework for leakages and tighten them if essential. Fill the tub as well as additionally check the overflow outlet as well as the regular electrical outlet for leaks.
Finally, take care of the bathroom paneling as defined in the supplier's instruction manual. Tiling and sealing around the bathtub should wait until the bathtub has actually been made use of at the very least when as this will certainly resolve it into its final position.
Suitable New Touches
If the tails of the new taps are plastic, then you will certainly require a plastic port to stop damages to the string. One end of the adapter fits on the plastic tail of the faucet and the various other end provides a link to the existing supply pipelines.
If you require to fit a monobloc, after that you will require lowering couplers, which links the 10mm pipeline of the monobloc to the typical 15mm supply pipe.
Next, position the faucet in the placing hole in the bath/basin guaranteeing that the washing machines remain in place in between the faucet and the sink. Safeguard the faucet in place with the maker provided backnut. When the faucet is firmly in place, the supply pipes can be linked to the tails of the faucets. The faucets can either be attached by utilizing corrugated copper piping or with normal tap connectors. The former type ought to be linked to the tap ends first, tightening only by hand. The supply pipes can later be connected to the other end. Tighten up both ends with a spanner after both ends have actually been attached.
Tiling Around the Bathtub
In the area where the bathroom fulfills the ceramic tile, it is needed to seal the joins with a silicone rubber caulking. This is essential as the installation can move sufficient to split an inflexible seal, causing the water to permeate the wall surface in between the bathroom and the tiling, causing issues with moisture and also possible leakages to the ceiling below.
You can pick from a range of coloured sealers to blend in your components and also fittings. They are sold in tubes as well as cartridges, and are capable of securing voids as much as a size of 3mm (1/8 inch). If you have a bigger gap to fill, you can load it with spins of drenched newspaper or soft rope. Keep in mind to constantly load the bath tub with water prior to sealing, to allow for the motion experienced when the tub is in usage. The sealer can split rather very early if you do not consider this motion before sealing.
Alternatively, ceramic coving or quadrant ceramic tiles can be utilized to edge the bath or shower tray. Plastic strips of coving, which are easy to use and reduce to size, are also easily readily available on the marketplace. It is suggested to fit the ceramic tiles utilizing water-resistant or waterproof glue and also grout.
How to Install or Replace a Bathtub
Find Your Dimensions
The first step in any bathtub installation or replacement is to select the right size tub for your bathroom. Start by measuring your existing bathtub’s alcove from wall to wall. The standard size for bathtubs is around 5 feet long and 30 or 32 inches wide. Purchase the size that’s closest to your previous tub.
After you’ve measured, you’ll need to figure out what type of tub you need. Face the alcove. If the drain is on the right-hand side, you’ll need a right drain tub. If it’s on the left, get a left drain tub. Easy enough, right?
Disconnect the Water Supply and Drain Assembly
Before you can start on your removal, make sure that you turn off the tub’s water supply. Some bathrooms have a shutoff valve, but if you don’t see one, you’ll need to turn off the supply at your house’s water main. Once the water’s off, open the valves to release any remaining air in the supply lines.
Then, disconnect the tub drain flange. This process varies based on the type of drain you have, but in most cases, you’ll need a drain flange removal tool to perform this task. If you’re feeling handy, you might be able to use a pair of needle-nose pliers to twist and pull the flange.
Now comes the fun part. In order to disconnect the drain assembly, you’ll need to be able to get to the space underneath the tub. You might need to access the tub drain from a crawlspace or a basement. Don’t forget to take a pipe wrench with you, as you’ll need it to loosen the pipe at the connection.
Cut Out the Old Tub
After removing the drainpipe assembly, you can take out the old bathtub. Cut a strip above the tub edge in the wall surrounding the bathtub that's about 6 inches in height. The tools you need here may vary depending on the type of wall surround you have in the alcove. If you’re cutting drywall, use a drywall saw and remove the section of the wall all the way down to the studs. If you have tile, you’ll need to use a grinder with a diamond blade to cut through the grout line. Then, use a chisel to remove the individual tiles. Take care here not to cut through any studs.
Find the tub flange. Remove the screws that attach the flange to the studs in the wall. At this point, the tub should be freed from the wall.
Once you’ve removed the flange, use a utility knife to cut away the caulk between the tub and the floor. When this is done, you should be able to lift the tub up and out of the alcove. Keep in mind that, depending on what it’s made of, the old tub could be tremendously heavy. You should plan to have a friend help you move it just in case.
Install the New Tub
Before you make any adjustments to the area, place the new tub in the alcove to make sure it fits properly and that the tub drain lines up with the P-trap underneath the floor.
Remove it and install a 2 x 4 ledger board. Measure the tub’s flange, then mark that height on the wall. Screw the ledger board to studs in the wall. This will help to support the weight of the tub.
Once the ledger board has been installed, go ahead and secure the drain to the tub. For this step, you’ll need some plumber’s putty. Roll a small amount of putty in your hands and wrap it around the underside of the drain flange. Push the drain into the tub from underneath the tub.
When the drain has been attached, connect the overflow drain. To do this, you’ll place the gasket on the overflow elbow and move it behind the tub. Once that’s on, connect the overflow pipe and the drainpipe, but take care not to overtighten.
Secure the Tub
After the connections are in, it’s time to set the tub in place. Before you start, make sure the flange lines up with the markings you made in Step 4. Because the ledger board holds the tub in place, it’s important that it matches up. If not, you’ll need to remove it and readjust.
Once your measurements line up, attach the flange to the studs on all three sides of the wall. Please note that you should not screw the flange to the wall. Instead, you should use roofing nails because they won’t rust over time. When the tub is in place, install the baseboard and the molding in front of and around the tub.
Repair and finish off the drywall or tile that you cut in Step 3. If you’re installing a fiberglass bath surround, now’s the time to adhere it to the alcove.
Then, enjoy your tub! While all these steps might seem intimidating, removing and installing a new bathtub is a relatively easy DIY project that can be completed in a single day. And now, when you settle in for your next bubbly soak, you can enjoy your bath without the distraction of a tub in disrepair.
https://www.homeserve.com/en-us/blog/how-to/bathtub-replacement/
I am just very eager about How to Install a Bathtub Yourself and I am praying you liked my article. For those who enjoyed our blog posting plz be sure to share it. We recognize the value of reading our article about How to Install a Bathtub.
Book-Now Report this page